Объект - одиночный NW 5.1 SP 8 сервер. Имеет 2 сетевых интерфейса. К одному привязан IPX на _802.2, к другому IP на _II. Настроен, ессссно, как End Node.
Однако команда protocols сообщает, что
The following protocols are registered:
Protocol: IPX Frame type: VIRTUAL_LAN Protocol ID: 0
Protocol: ARP Frame type: ETHERNET_II Protocol ID: 806
Protocol: IP Frame type: ETHERNET_II Protocol ID: 800
Protocol: IPX Frame type: ETHERNET_II Protocol ID: 8137
Protocol: IPX Frame type: ETHERNET_802.2 Protocol ID: E0
Поневоле возникает вопрос - а откуда лишние протоколы? особенно IPX на Ethernet_II?
Вот NetInfo.CFG
#!VERSION=2.3
#!
#! --- WARNING -- WARNING -- WARNING -- WARNING -- WARNING -- WARNING ----
#! This file was created by the Internetworking Configuration Console.
#! It is intended to be modified ONLY by the configurator (INETCFG.NLM).
#! Tampering with this file may cause severe malfunctioning of the system.
#! The configurator will check for tampering and abort if it is detected.
#! -----------------------------------------------------------------------
#!
#!SERVERTYPE=NORMAL
#!
#!UIMODE=NORMAL
#!
#!BEGINGENLOAD
LOAD SNMP
LOAD BCALLSRV
#!END
#!
#!BEGINTSMLOAD
#!END
#!
#!BEGINBOARD DRVR=CE1000 NAME=CE1000_1 STATUS=ENABLED NUMPORTS=1 DRVRTYPE=LAN VARIABLEPORTS=NO PORTPARAM=CHANNEL SLOT=10019
#
#!BEGINPORT NAME=CE1000_1 NUMBER=1 STATUS=ENABLED FRAMES=YES NUMLINKS=0 MEDIA=EtherTsm WANFRAME=UNCONFIGURED
#
#!REFCOUNT=1
LOAD CE1000 NAME=CE1000_1_EII FRAME=ETHERNET_II SLOT=10019
#!END
#!END
#!
#!BEGINBOARD DRVR=CE1000 NAME=CE1000_2 STATUS=ENABLED NUMPORTS=1 DRVRTYPE=LAN VARIABLEPORTS=NO PORTPARAM=CHANNEL SLOT=10020
#
#!BEGINPORT NAME=CE1000_2 NUMBER=1 STATUS=ENABLED FRAMES=YES NUMLINKS=0 MEDIA=EtherTsm WANFRAME=UNCONFIGURED
#
#!REFCOUNT=1
LOAD CE1000 NAME=CE1000_2_E82 FRAME=Ethernet_802.2 SLOT=10020
#!END
#!END
#!
#!BEGINPROTO PROTO=TCPIP STATUS=ENABLED
LOAD Tcpip RIP=No Static=Yes LoadSharing=Yes Forward=No
#
#!BEGINBIND STATUS=ENABLED
BIND IP CE1000_1_EII ARP=Yes Mask=255.255.255.0 Address=192.168.0.127
#192.168.0.127
#!END
#!END
#!
#!BEGINPROTO PROTO=IPX STATUS=ENABLED
SET Reply To Get Nearest Server=ON
#
LOAD IPXRTR ROUTING=NONE CFGDIR=SYS:ETC SEQ=2
#
LOAD IPXRTRNM SEQ=2
#
LOAD SPXCONFG Q=1 A=540 V=54 W=108 R=10 S=1000 I=1200
#
SET IPX NetBIOS Replication Option=1
#
SET Load Balance Local LAN=OFF
#
#!BEGINBIND STATUS=ENABLED
BIND IPX CE1000_2_E82 net=fffff2 seq=1
#fffff2
#!END
#!END
#!
#!BEGINPROTO PROTO=APPLETLK STATUS=DISABLED
#:LOAD LLC8022
#
#:LOAD AppleTlk zfile=Yes
#
#:LOAD adsp
#
#!END
#!
#!BEGINPROTO PROTO=SRBRIDGE STATUS=DISABLED
#:LOAD BRIDGE BN=1 VRN=OFF ARL=8 STP=IEEE SBP=0x8000 SRL=8 G=SRB BTS=250
#
#!END
#!
#!BEGINPROTO PROTO=SRCROUTE STATUS=DISABLED
#!END
#!
#!BEGINPROTO PROTO=ODINEB.N STATUS=ENABLED
LOAD ODINEB.NLM
#
#!END
#!
#!BEGINPROTO PROTO=ODINEB.N STATUS=ENABLED
LOAD ODINEB.NLM
#
#!END
