Логин при включении компьютера

Обсуждение технических вопросов по продуктам Novell

Логин при включении компьютера

Сообщение Сергей Терехов » 06 июн 2002, 08:24

Подскажите как разрешить небольшую, но занудную проблемку. Есть сеть на 30 машин, под управление Novell 5.0 SP6 и рабочие станции под Win98SE на них установленны сетевые карты Intel и 3COM , так вот, при включении машины с установленной интеловской картой окно логина появляется без проблем, а если трикомовская, то не получается, и после загрузки винды приходится принудительно вызывать окно логина. Причем версию клиента во втором случае приходится ставить только 3.3, иначе логиниться не получается вообще. На интеловских машинах стоят 3.1 Интересно, в чем могут быть грабли?
Сергей Терехов
 

Про грабли ))

Сообщение Ivan » 06 июн 2002, 08:59

И все таки виноваты скорее всего не "клиенты" и не ланки.
Причина по видимому в корректной установке 3СОМ.
Проверь цепочку "мамка"-"3СОМ"-"винды"
Ivan
 
Сообщения: 24
Зарегистрирован: 05 июн 2002, 09:39
Откуда: Москва

Настройте 3COM

Сообщение Владимир Горяев » 06 июн 2002, 09:32

т.е. отмените автонастройки.Принудительно выставте параметры утилитой от 3COM.
Бардак автоматизировать невозможно!!!
_________________
Аватара пользователя
Владимир Горяев
 
Сообщения: 3473
Зарегистрирован: 05 июн 2002, 13:37
Откуда: Смоленск

Сообщение Юра Кан » 06 июн 2002, 18:08

60 машин на 3с905(B,C) + NW4.11 SP8a 2 года полет нормальный. Настройки платы утилитой от 3com в автомате. Скорее всего дело в версиях драйверов для 3com и установки драйверов в виндах
Юра Кан
 
Сообщения: 116
Зарегистрирован: 06 июн 2002, 17:39

Сообщение Стогов Кирилл » 08 июн 2002, 01:33

Доброй ночи ura68. Если бы ты лучше описал ситуацию, ответ был бы короче. Этот Тид с 3Com-а должен помочь. У самого когда-то была такая ситуация. Тид за 3 года вырос неимоверно, но остался на своем месте.
Еще, ты ничего не пишешь о сетевом оборудовании. Но если есть свичи, то неплохо бы отключить поддержку spanning tree.
Успехов.

SolutionID:
112.0.1788980.1576222
Title: 3C905B-TX - Microsoft Windows - Novell NetWare - Cannot connect to NetWare server

Fact 3C905B-TX

Fact 3C905B


Symptom Cannot connect to NetWare server

Symptom No NetWare logon prompt upon reboot

Symptom Extremely slow login and network connection

Symptom Client unable to login to Novell Server

Symptom Specified IP address in Network Settings

Symptom Extremely slow login when connecting to Novell Netware
Note: This symptom may or may not appear

Symptom Cannot connect with IPX/SPX after configuring TCP/IP

Symptom No login prompt
Note: This symptom may or may not appear

Symptom Rconsole does not show servers


Fact OS: Microsoft Windows 95 OSR2

Fact OS: Microsoft Windows 95

Fact OS: Microsoft Windows 98

Fact OS: Microsoft Windows NT 4.0

Fact NOS: Novell NetWare

Fact Novell NetWare Client 32

Fact Works with DHCP or Server Assigned IP Address


Fix Set the frame type for the 3C905B-TX:

For Microsoft Windows 95 and Microsoft Windows 98:
1. START>SETTINGS>CONTROL PANEL>NETWORK
2. In Network Configuration tab, double-click IPX/SPX-compatible Protocol (Note: If IPX/SPX is listed more than once, select the one that is bound to 3Com)
3. Click the Advanced tab
4. Highlight Frame Type in the Property window
5. Arrow down next to the word "Auto" (on the right) and select the appropriate frame type: Ethernet 802.2, Ethernet 802.3
6. Click OK
7. Click OK again
8. Click YES to restart computer
NOTE: If using Novell Client 32, repeat the above procedure for IPX 32-bit Protocol, so that the frame is set for both IPX/SPX and IPX 32-bit protocols.

For Microsoft Windows NT 4.0:
1. START>SETTINGS>CONTROL PANEL>NETWORK
2. Click the Protocols tab, double-click NWLink IPX/SPX Compatible Transport
3. In the General tab, click on the down arrow next to Frame Type
4. Select the appropriate frame type: Ethernet 802.2, Ethernet 802.3
5. Click OK
6. Click OK again
7. Click YES to restart computer

Fix If frame type is already set, and NetWare login still does not appear:
For Microsoft Windows 95 or Microsoft Windows 98:
1. START>SETTINGS>CONTROL PANEL>NETWORK
2. In Network Configuration tab, double-click IPX/SPX-compatible Protocol (Note: If IPX/SPX is listed more than once, select the one that is bound to 3Com)
3. Click the ADVANCED tab
4. Highlight MAXIMUM CONNECTIONS
5. Change the Value from Not Set to 16
6. Highlight MAXIMUM SOCKETS
7. Change the Value from Not Set to 32
8. Click OK
9. Click OK again
10. Click YES to restart computer

Fix If the Novell NetWare logon prompt still does not appear, set the media type:
1. For Microsoft Windows 95 or Microsoft Windows NT 4.0:
a. Double-click the 3Com tray icon (lower right corner of desktop)
b. Click on the Properties tab
c. Click on Media Type
d. Click on the arrow bar on the right side, next to Auto
e. Select 10BASE-T or 100BASE-TX, depending on what speed your hub or switch is using
Note: The corresponding duplex setting should automatically be set
f. Click OK
g. Exit the diagnostics program
h. Restart Microsoft Windows 95
2. For other operating systems:
a. Boot with a DOS-bootable diskette
b. At the A:\> prompt, type: 3C90XCFG and press Enter
c. Press F4 to "Configure NIC"
d. Change the media type on the NIC to the appropriate speed:
i. Press TAB until Network Optimization is highlighted
ii. Press the down arrow to get to Media Type
iii. Press Enter
iv. Select 10BASE-T or 100BASE-TX, depending on what speed your hub or switch is using
Note: The corresponding duplex setting should automatically be set
e. Save the configuration to the NIC:
i. Press TAB until OK is highlighted
ii. Press Enter. NOTE: A message stating that the configuration has been saved to the NIC will be displayed.
iii. Restart the computer

Fix If the above fixes do not resolve the issue, install the current shipping driver EtherDisk v4.x or greater
Note: The current driver for the 3C90x Family can be found at: www.3Com.com


Fact Search group - 3C905

Fact Search group - Desktop Ethernet NICs

Fact Last Reviewed: April 2002
Стогов Кирилл
 

Логин при включении компьютера

Сообщение Сергей Терехов » 08 июн 2002, 13:09

Спасибо всем. Проблема решилась после установки 3 сервис пака для клиента 3.3
Сергей Терехов
 
Сообщения: 2
Зарегистрирован: 06 июн 2002, 10:46
Откуда: Тюмень. Тюменская обл.


Вернуться в Novell

Кто сейчас на конференции

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 65