Урал » 27 окт 2007, 12:35
Стоит ZEN 7. На сервере поднят DHCP сервер, прописана опция 60.
На этом же сервере установлен ZEN, TFTP, PDHCP и прочие службы.
Старутую службы, на ноуте выбираю загрузку по PXE.
Станция опрашивает DHCP, получает адрес.
Дальше надпись на экране:
Auto select:
ZENWorks boot
BOOT server IP: 192.168.1.1
PXE-E35: TFTP read timeout
PXE-E39: TFTP cannot read from connection
PXE-M0F: Exiting Broadcom PXE ROM
Operating system not found
Вот содержимое папок:
Том в устройстве F имеет метку SYS
Серийный номер тома: C0A8-0101
Содержимое папки F:\tftp
23.10.2007 10:27 <DIR> .
23.10.2007 10:27 <DIR> ..
15.11.2005 23:12 3 680 BOOT.DNX
27.07.2005 02:18 734 DEFMENU.DAT
23.06.2006 01:26 24 066 DINIC.SYS
13.06.2006 21:46 7 613 494 initrd
21.06.2006 01:28 5 008 LOADLIN.DNX
26.01.2005 02:52 6 513 Menu.dnx
23.10.2007 10:29 <DIR> boot
23.10.2007 10:30 <DIR> cmds
7 файлов 7 653 635 байт
4 папок 21 393 727 488 байт свободно
Том в устройстве F имеет метку SYS
Серийный номер тома: C0A8-0101
Содержимое папки F:\tftp\boot
23.10.2007 10:29 <DIR> .
23.10.2007 10:29 <DIR> ..
23.06.2006 01:26 24 066 DINIC.SYS
13.06.2006 21:46 7 613 494 initrd
10.02.2006 23:07 1 544 369 linux
13.06.2006 21:46 13 890 779 root
16.05.2006 04:34 1 702 settings.txt
6 файлов 23 074 555 байт
2 папок 21 393 727 488 байт свободно
вот содержимое tftp.ini
#
# This is a sample tftp.ini file
#
# The default values are:
# ReadPath=SYS:\tftp\
# WriteProtect=1
# BlksizeDisabled=0
# IPADDRESS=127.0.0.1 ipaddress to bind to
# The ReadPath setting is used for both TFTP file reads and writes.
ReadPath=SYS:\tftp\
WriteProtect=1
BlksizeDisabled=0
IPADDRESS=192.168.1.1
# end of file
ЭТО PDHCP.INI
#---------------------------------------------------------------------------
# This is the configuration file for the ZENworks Preboot Proxy DHCP server.
#
# By default all the options in this configuration file are commented out.
# For most installations this is the correct configuration.
#
#---------------------------------------------------------------------------
# Setting VERBOSE to 1 will cause the server to write additional configuration
# information to the console as it starts.
VERBOSE=1
#---------------------------------------------------------------------------
# IP ADDRESS SETTINGS
#
# When an option is NOT specified in this file, the server will automatically
# supply the server IP address to a PXE client.
# In the case of a multihomed server the Proxy DHCP server will supply the
# server IP address of the network adapter that received the request.
#
# If the Proxy DHCP server is running on a different server to the
# Transaction and TFTP servers, then uncomment the relevant fields and set
# them to the IP address of the server running Transaction server (DTS.NLM)
# and TFTP server (TFTP.NLM).
#---------------------------------------------------------------------------
# The Preboot client will contact the server on this IP address to check for
# imaging work.
#TRANSACTION_SERVER_IP=192.168.1.1
# The PXE/Preboot client will contact the server on this IP address to
# download the Preboot client (dinic.sys) and the Imaging engine if
# imaging work is required.
TFTP_SERVER_IP=192.168.1.1
# If set the Proxy DHCP server will try to bind to this IP address on the
# server.
# The IP address set must be a valid IP address on the server.
# This setting can be used to force the PDHCP server to respond on only one
# interface on a multihomed server.
PDHCP_Server_IP=192.168.1.1
# Should the Proxy DHCP server listen on the dhcp port 67
USE_DHCP_PORT=0
USE_BINL_PORT=1
#---------------------------------------------------------------------------
# PXE specific options
#---------------------------------------------------------------------------
# This settings controls how long the PXE boot menu is displayed as
# a PXE workstation boots.
BOOT_MENU_TIMEOUT=0
# Set this option to 0 to disable multicast TFTP transfers. This is the
# default setting.
# Set this option to 1 to enable multicast TFTP transfers. In this mode
# the PXE client will wait to join a multicast group for the transfer of
# the initial dinic.sys file. Enabling this option will add 10 to 20
# seconds to the PXE boot up sequence, so this is not recommended.
#USE_MTFTP=0
# This value specifies the multicast IP that the server should use for
# MTFTP transfers.
#MTFTP_IP=234.0.0.0
#This value specifies the server port to use for MTFTP transfers.
#MTFTP_SERVER_PORT=360
#This value specifies the client port to use for MTFTP transfers.
#MTFTP_CLIENT_PORT=1000
# Sets the time to wait before opening the MTFTP session.
#MTFTP_OPEN_TIMEOUT=2
# Sets the time to wait before reopening the MTFTP session.
MTFTP_REOPEN_TIMEOUT=2
# end of file
Адрес сервера 192.168.1.1
После RXEStart вот лог загрузки
Loading module TFTP.NLM
ZENworks Preboot TFTP Server
Version 2.05.01 27 February 2006
(C) 2001-2004 PreWorX (PTY) Ltd
Module TFTP.NLM load status OK
Using SYS:\tftp\ from SYS:\SYSTEM\TFTP.INI as TFTP data directory.
Using IP Address (192.168.1.1) Specified in Ini file.
Loading module PDHCP.NLM
Di-NIC Proxy DHCP Server
Version 2.08 20 October 2003
(C) Copyright 2000-2002 PreWorX (PTY) Ltd
Module PDHCP.NLM load status OK
Reading Proxy DHCP configuration from SYS:\SYSTEM\PDHCP.INI.
The Proxy DHCP Server IP address has been set in PDHCP.INI and will not be detec
ted.
Detected the following addresses on this server:
192.168.1.1
192.168.2.2
Binding to 192.168.1.1 on port 4011 ... SUCCESS
Loading module DTS.NLM
Transaction Server 3.1.0 - Netware
Version 3.01.03 20 June 2006
(C) Copyright PreWorX 2000-2005. All Rights Reserved.
Auto-loading module ZENPXE.NLM
ZENworks Imaging PXE Library
Version 7.00 13 June 2006
Copyright 2001, 2002, 2003 Novell, Inc.
Module ZENPXE.NLM load status OK
Auto-Loading Module PMAP.NLM
Auto-loading module PMAP.NLM
ZENworks Port Mapper Service
Version 2.01 15 September 2005
(c) Copyright 2001 PreWorx (Pty) Ltd.
Module PMAP.NLM load status OK
PMAP : InitializeDebug logger...
PMAP : Log filename [SYS:SYSTEM\PMAP.LOG]...
Module DTS.NLM load status OK
Default settings filename [SYS:\SYSTEM\DTS.INI]...
PMAP : Cluster IP Address not set, using local IP Address.
PMAP : Binding to SUN RPC Port 111...
PMAP : UDP port 111 is already in use.
PMAP : Port mapper shutting down..
Logging Disabled...
ServerUDPPort not defined in SYS:\SYSTEM\DTS.INI. Using default port 18753
TS Cluster IP Address not set. Using local IP Address for ZENPXE.
Transaction Server started...
Почему не удается загрузиться?
Что не хватает? И кто держит 111 порт, как узнать?