Андрей Тр. aka RH, спасибо. Кстати в иннете не нашёл ничего по консольным командам. Это странно. Наверное не там искал. В общем RTFM, но его тоже ещё надо найти
Вообще-то при ( даже перед ) инсталляции собственно Netware на винте обычно создают раздел ДОС, и с него уже запускается server.exe, именно из autoexec.bat ( при этом есть кое-какие рекомендации по config.sys ). Все это должно быть в Installation Guide, да и инсталлятор обычно в конце предлагает обновить autoexec и config.
Теперь я это уже тоже понял
Инсталлятор ничего не предлагал мне обновить, но partitions я создал в процессе инсталляции NetWare (теперь мне понятно, что это криво, надо было всё fdids`ом сделать и DOS ставить до установки NetWare).
Вопросы.
1. Я сейчас пытаюсь сделать sys a: c: (DOS 6.22), так он ругается "No room for system on destination disk". Мануал по этому поводу говорит следующее:
When you execute the SYS command, you are usually greeted by one of two messages:
System transferred
or
No room for system on destination disk
If a disk has data on it before you try to write the system files to it, the SYS command from DOS versions 3.3 and earlier probably will fail because they are not capable of moving other files out of the way. The SYS command in DOS 4.0 and higher versions rarely fail because they can move files out of the way.
Some users think that the cause of the No room message on a system that has an older version of DOS is that the system files in any newer version of DOS are always larger than the previous version, and that the new version files cannot fit into the space allocated for older versions. Such users believe that the command fails because this space cannot be provided at the beginning without moving other data away. This is incorrect. The SYS command fails in these cases because you are trying to install a version of DOS that has file names different from those already on the disk. There is no normal reason for the SYS command to fail when you update the system files on a disk that already has them.
The system files can be placed virtually anywhere on the disk, except that the first clusters of the disk must contain the first cluster of the IO.SYS file (or its equivalent). As long as that requirement is met, the IO.SYS and MSDOS.SYS files can be fragmented and placed just about anywhere on the disk, and the SYS command implements them with no problems whatsoever. The only other requirement is that the names IO.SYS and MSDOS.SYS (or their equivalents) must use the first and second directory entries.
Это всё здорово, но как мне теперь сделать C: системным? Или всё, поезд уехал, надо заново NetWare переставлять?
2. Может кто-нибудь кинет пример необходимых мне autoexec.bat и config.sys? Что-нибудь общего плана, дальше я уже сам разберусь.
3. Насколько я понял ОС всё-таки должна быть установлена (DOS), а server это что-то вроде сервиса, который запускается поверх операционной сиситемы. Правильно? А startup.ncf выполняется при запуске server.
В связи с этим вопрос:
"
Обратите внимание, что том SYS: монтируется автоматически при загрузке соответствующего дискового драйвера в процессе выполнения файла STARTUP.NCF."
Я обратил внимание
, жалко только не понял в какой строке это описано.
И как только монтируется SYS: сразу исполняется autoexec.ncf
Чем больше разбираешься, тем больше вопросов - см. мою подпись