NetWare Message File: CMSM.nlm 1.00, Tran v1.0 xàô  7Oi‚š´Ïêù)@Wq‹Ÿ¶ÅÜ;Sh›Ü#PŠŽ·íý'W‹ÊÙ-au‡Öß$')0<AGQ^mt‘˜ ¨®·¾ÃËÒ×ßçòý   & + 2 : ? C H J x ª Ó à ë   U W m q | ‹ Ž ‘ ¢ ¬ ° ³ Ø  T Z ‚ † ž Å ý @ <<< BAD MESSAGE >>>Total Tx Packet CountTotal Rx Packet CountNo ECB Available CountPacket Tx Too Big CountPacket Tx Too Small CountPacket Rx Overflow CountPacket Rx Too Big CountPacket Rx Too Small CountPacket Tx Misc Error CountPacket Rx Misc Error CountRetry Tx CountChecksum Error CountHardware Tx Mismatch CountTotal Rx OK Byte CountTotal Tx OK Byte CountTotal Group Addr Tx CountTotal Group Addr Rx CountAdapter Reset CountAdapter Opr Time StampTx Queue DepthCMSM Init Alloc MemoryCMSM-NW-072: A resource tag is unavailableFATAL: Unable to reset MLID. Unloading module %s. CMSM Event NotificationCMSM Polling RoutineCMSM-NW-76: The polling procedure cannot be added.CMSM-NW-77: The event notification routine cannot be registered.%s-NW-%03d: Cannot add polling without an HSM routine. %s MLID Board%s-NW-%03d: A resource tag is unavailable. %s-NW-%03d: The MLID cannot be registered with the LSL. IPX%s-NW-%03d: Unable to allocate memory. %s-NW-%03d: The media parameter block is too small. %s Alloc Memory%s Cache Below 16 Meg%s Hardware Options%s-NW-%03d: The firmware file cannot be read. %s-NW-%03d: The hardware configuration conflicts. %s-NW-%03d: The matching virtual adapter could not be found. %s ECB Buffers%s-NW-%03d: Cannot set hardware interrupt without an HSM routine. %s Hardware ISR%s-NW-%03d: The hardware interrupt cannot be set. %s Timer Call-Backs%s AES Call-BacksABEND, ECB Linear Address with no Physical Address, address not locked down. %.8s-NW-%.8s-NW-Adapter %x-Board %x: %s%.8s-NW-Adapter %x-Board %x: %d:%s . using I/O ports to and , Memory , Interrupt , DMA Channel SLOT Select Board To Load : 10INT=%XINT1=%XPORT=%XPORT0PORT1=%XDMA=%XDMA0DMA1=%XMEM=%XMEM0MEM1=%XSLOT=%UCHANNEL=%URETRIES=%UBUFFERS16=%UBUFFERS16BELOW16NODE=%16sNODEBUS=%sNAME=%sINT0 =]Board name is too long and was truncated: %s Board name %s is already in use and was ignored. Expected board name missing or invalid. -+012345678901234567890123456789ABCDEFabcdef ..~YyNnDo you want to load another frame type for a previously loaded board? : n Enter the value for : Supported values are : . , Enter Value for between - %sCommand Line Parameter Prompt for %s%s-NW-%03d: The specified node address override is invalidA Keyword was out of range or a required parameter is missing. FRAMEEvent registration with NESL failed. LSBODI_CSPEC_VERSION: 1.10Error parsing for driver parameter. VeRsIoN=1.00 Novell Media Support Module message file.CoPyRiGhT=(c) Copyright 1996, by Novell, Inc. All rights reserved.LaNgUaGe= English (English)